How We Repair Your Hobart Glass Washer
Dishwashers fill, heat, spray and drain water using an inlet valve, a circulation pump, a drain pump, a heater and a control board.
Every Hobart model has its own parts list, so we start with the model and serial number on the rating label. That tells us the correct parts and any known issues or service bulletins for your unit.
Common Glass Washer Problems We Fix
Not draining
A clogged filter or drain hose, a blocked garbage disposal connection or a failed drain pump.
Dishes not clean
A dirty filter, clogged spray arms, low water temperature or a weak circulation pump.
Leaking
A worn door gasket, a loose hose clamp, a cracked tub or a failing pump seal.
Not filling
A failed water inlet valve, a float switch stuck up or a closed supply valve.
Not drying
A burned-out heating element, a failed fan or no rinse aid.
Will not start
A door latch switch, a control board or a tripped thermal fuse.
Quick Checks Before You Call
These are safe for most owners and sometimes solve the problem without a visit:
- Clean the filter at the bottom of the tub.
- Run the kitchen tap hot before starting a cycle.
- Make sure the disposal knockout plug was removed if one was installed recently.
- Check the float in the front corner moves freely.
Still not working? Call (844) 442-1500 or try our troubleshooting wizard.
Our 5-Step Repair Process
- Call or book onlineTell us what your Hobart glass washer is doing and when it started. We schedule the first available visit.
- DiagnosisThe technician checks power, controls and the parts most likely to fail, using the model's service data and test modes.
- Upfront quoteYou get the cause, the repair and the price before any work starts. If repair does not make sense, we tell you.
- RepairWe install original or equivalent parts matched to your model and clean up when we are done.
- Test and warrantyWe run the appliance through a full cycle to confirm the fix. The repair is covered by our 90-day parts and labor warranty.
Parts We Replace Most Often
- Drain pump
- Circulation pump and motor
- Water inlet valve
- Heating element
- Door latch
- Door gasket
- Control board
- Spray arms
Cost and Lifespan
Most glass washer repairs cost $150–$400 including parts and labor, and these appliances typically last 9–12 years. These are national estimates: your exact price comes after the diagnosis. Use the repair vs replace calculator to compare.
Keep It Running Longer
- Use rinse aid
- Run a cleaning cycle monthly, more often with hard water
- Clean the filter monthly
Glass Washer Repair in New York
We repair glass washers in 701 cities and towns across New York. Humid summers and long, cold winters in New York give homes across the state appliances a busy year, with heavy indoor use from fall to spring.
Frequently Asked Questions
How much does Hobart Glass Washer Repair cost in New York?
Most glass washer repairs fall between $150–$400 including parts and labor. The final price depends on the part that failed and your model. You get an exact quote after the diagnosis and before any work starts.
Can you repair my glass washer today?
Same-day visits depend on technician availability in New York. Call (844) 442-1500 early in the day for the best chance of a same-day or next-day appointment.
Is the repair guaranteed?
Yes. Parts and labor are covered by our 90-day warranty. If the same problem comes back within that time, we return and fix it.
Do you work on all Hobart models?
We repair current and older Hobart models. Some discontinued parts can be hard to find; if that is the case for your model, we tell you before you pay for a repair.
Should I repair or replace my glass washer?
A glass washer typically lasts about 9 to 12 years. If yours is well inside that range and the repair costs less than half the price of a new one, repairing usually makes sense. Near the end of its life, or when the repair costs more than half of a replacement, replacing is often the better value. We give you an honest opinion either way.